G O D R I V E G R S 8 0 S QUANTUM
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 2.5"/SUPERSLIMLINE Cylinders | | |
Capacity form/unform 84/ MB Heads | | |
Seek time / track 17.0/ ms Sector/track | | |
Controller SCSI2 SINGLE-ENDED Precompensation 65535
Cache/Buffer 32 KB Landing Zone
Data transfer rate MB/S int Bytes/Sector 512
4.000 MB/S ext ASYNC
Recording method RLL operating | non-operating
-------------+--------------
Supply voltage 5 V Temperature *C |
Power: sleep W Humidity % |
standby W Altitude km |
idle W Shock g 10 | 100
seek W Rotation RPM
read/write W Acoustic dBA
spin-up W ECC Bit
MTBF h 150000
Warranty Month 12
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
QUANTUM GRS80/160S UNIVERSAL CONFIGURATION GUIDE 81-100399-10 10/95
+--------------------------------------------------+
| |
| |
+--------------------------J1----------------J2----+
|+------------------------------------------------+|
||o o o o o o o o o o o . o o o o o o o 1 o o o 1||
||o o o o o o o o o o o o o o o o o o o 2 o o o o||
|40-----------------------------------------------+|
+-----------SCSI-----------------------------------+
+ +
J1 and J2 are fabricated from one 50-pin connector. J1 has 40 pins,
J2 has 8 pins, and 2 pins have been removed at the boundry between
J2 and J1.
**********************************************************************
J U M P E R S
**********************************************************************
QUANTUM GRS80/160S UNIVERSAL INSTALLATION GUIDE 81-100399-10 10/95
Jumper Setting
==============
x = Factory default
GoDrive GRS 80/160 S drives have a single 2 x 25 connector (on 2mm
centers) for both power and data. The connector also includes four
pins which are used as factory test points (these pins must be
allowed to float), for the SCSI device ID (J2 pins 5 through 7), and
for a drive activity LED (J2 pin 8).
J2 SCSI ID
-----------
+----------+-----------------------+
| SCSI ID | Pins |
| | 7 | 6 | 5 |
+----------+-------+-------+-------+
|x 0 | OPEN | OPEN | OPEN |
+----------+-------+-------+-------+
| 1 | OPEN | OPEN | GROUND|
+----------+-------+-------+-------+
| 2 | OPEN | GROUND| OPEN |
+----------+-------+-------+-------+
| 3 | OPEN | GROUND| GROUND|
+----------+-------+-------+-------+
| 4 | GROUND| OPEN | OPEN |
+----------+-------+-------+-------+
| 5 | GROUND| OPEN | GROUND|
+----------+-------+-------+-------+
| 6 | GROUND| GROUND| OPEN |
+----------+-------+-------+-------+
| 7 | GROUND| GROUND| GROUND|
+----------+-------+-------+-------+
**********************************************************************
I N S T A L L
**********************************************************************
QUANTUM GRS80/160S UNIVERSAL INSTALLATION GUIDE 81-100399-10 10/95
Notes on Installation
=====================
Installation direction
----------------------
horizontally vertically
+-----------------+ +--+ +--+
| | | +-----+ +-----+ |
| | | | | | | |
+-+-----------------+-+ | | | | | |
+---------------------+ | | | | | |
| | | | | |
| | | | | |
+---------------------+ | +-----+ +-----+ |
+-+-----------------+-+ +--+ +--+
| |
| |
+-----------------+
The drive will operate in all axis (6 directions).
Dimensions and Mounting
-----------------------
The drive can be mounted in any orientation. Maximum screw penetra-
tion is 3 mm with a minimum penetration of three full threads. The
maximum mounting torque for these screws is 40 inch-ounces.
NOTE
For optimum drive performance, the system mounting method should not
result in any disortion or twisting of the drive's base casting. For
example, if the drive is attached (via its bottom mounting holes) to
a stiff mounting surface that does not meet the GoDrive GLS flatness
requirements of 0.01 inch, then head switch times may be degraded.
The threaded holes in each of the four corners of the GoDrive GLS are
for top cover attachment only and should never be used for any other
purpose.
Cable Connector
---------------
GoDrive GRS 80/160 S drives have a single 2 x 25 connector (on 2mm
centers) for both power and data. The connector also includes four
pins which are used as factory test points (these pins must be
allowed to float) for the SCSI device ID (J2 pins 5 through 7), and
for a drive activity LED (J2 pin 8).
The recommended system mating connector is a 3M Series 150 50-pin
connector or equivalent. The maximum cable length is 18 inches. The
maximum cable length is 12 inches. To assure that the system cable
connector is installed with the proper orientation, plug Pin 17
hole on the J1 system connector.