T R A V E L S T A R 4 G N 2 2 1 6 0 IBM
Native| Translation
------+-----+-----+-----
Form 2.5"/SUPERSLIMLINE Cylinders | 4200| |
Capacity form/unform 2160/ MB Heads | 16| |
Seek time / track 2.8/ ms Sector/track | 63| |
Controller IDE / ATA3 ENHANCED Precompensation
Cache/Buffer 463 KB SEGMENTED Landing Zone
Data transfer rate 10.000 MB/S int Bytes/Sector 512
16.600 MB/S ext PIO4
Recording method operating | non-operating
-------------+--------------
Supply voltage 5 V Temperature *C 5 55 | -40 65
Power: sleep W Humidity % 8 90 | 5 95
standby W Altitude km -0.300 3.000| -0.300 12.000
idle W Shock g 150 | 700
seek W Rotation RPM 4200
read/write W Acoustic dBA
spin-up W ECC Bit SMART
MTBF h
Warranty Month
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
IBM DKLA-22160/23240/24320 JUMPER SETTING
+--------------------------------------+
| |
| |
| |
+--------Interface-------------49------+
| 43**********************1 **47 Jumper
| 44*************x********* **48 |
+------------------------------50------+
+ +
Pin position 20 is left blank for correct connector insertion.
Pin position 47 through 50 are used for drive address setting.
**********************************************************************
J U M P E R S
**********************************************************************
IBM DKLA-22160/23240/24320 JUMPER SETTING
Jumper Setting
==============
Drive Address Setting
---------------------
A jumper is available at the interface connector to determine the
drive address.
---49--47+
* * X | Slave
* * X |
---50--48+
---49--47+
* * * | Master
* * * |
---50--48+
---49--47+
* * * | Cable Selection
* xxx |
---50--48+
---49--47+
* xxx |
* * * | RESERVED Never attach a jumper here!
---50--48+
---49--47+
* X * | NEVER ATTACH A JUMPER HERE!!!
* X * |
---50--48+
Cable Selection
---------------
Using Cable Selection, the drive address depends on the condition of
pin 28 of the AT interface cable. In the case when pin 28 is ground
or low, the drive is a Master. If pin 28 is open or high level, the
drive is a Slave.
Cabling
-------
The maximum cable length from the host system to the HDD plus circuit
pattern in the host system shall not exceed 18 inches.
AT Signal Connector
-------------------
The AT signal connector is designed to mate with Dupont part number
69764-044 or equivalent.
**********************************************************************
I N S T A L L
**********************************************************************
IBM DKLA-22160/23240/24320 NOTES ON INSTALLATION
Notes on installation
=====================
Installation direction
----------------------
horizontally vertically
+-----------------+ +--+ +--+
| | | +-----+ +-----+ |
| | | | | | | |
+-+-----------------+-+ | | | | | |
+---------------------+ | | | | | |
| | | | | |
| | | | | |
+---------------------+ | +-----+ +-----+ |
+-+-----------------+-+ +--+ +--+
| |
| |
+-----------------+
The drive will operate in all axis (6 directions).
Performance and error rate will stay within specification limits if
the drive is operated in the other permissible orientations from
which it was formatted. Thus a drive formatted in a horizontal
orientation will be able to run vertically and vice versa.
The drive must be securely mounted in the system to prevent motion or
vibration during a seek operation or spindle rotation using
appropriate screws or equivalent mounting hardware.
The recommended mounting screw torque is 3.0 0.5 kgf.cm.
The recommended mounting screw depth is 3.0 0.3mm for bottom and
3.5 0.5mm for horizontal mounting.
Air Cooling Requirement
-----------------------
The host system must provide sufficient air flow across the drive to
maintain the temperature at less than 60*C (measured at the centre of
the files top cover).