SEAGATE TECHNOLOGY, INC.
     Customer Technical Support Bulletin Boards (300-9600, 8-N-1)
/----------------------------------+---------------------------------\
| United States    +1 408 438-8771 |  United Kingdom +44 628 478011  |
+----------------------------------+---------------------------------|
| Germany         +49  89 140-9331 |  Singapore      +65   227-2217  |
\----------------------------------+---------------------------------/
                            (C)opyright 1991



ST-1201NS (94351-200S) Swift SCSI
     /---\
     | O |  5
     | O |  G
     | O |  G
     | O | 12  ....................  o o o o o o
     \---/     1...................  o o o o o o
     ============================================
                                     1 2 4 | | |
                                     --+-- | | \- Synchronized Spindle
  Terminator Power Select              |   | \--- Motor Control
  Header located on the side           |   \----- Enable Parity Checking
  --------------------------           \--------- Drive ID, binary - use
 (Back) A B (Front of drive)                      ID 0 (no jumpers) for
        C D                                       single drive install
 A-B  Drive from Power Connector (factory default)
 A-C  Drive from SCSI Bus
 A-C&B-D  Drive from Power Connector and Provide to SCSI Bus
 B-D  Only provide to SCSI Bus

                    Shrouded SCSI Connector Only
     /---\
     | O |  5
     | O |  G
     | O |  G  /- If the SCSI connector has a plastic shroud, note pin-1
     | O | 12 +====================+ o o o o o o
     \---/    #:::::::::::::::::::1# o o o o o o
     ============================================
                                     1 2 4 | | |
                                     --+-- | | \- Synchronized Spindle
  Terminator Power Select              |   | \--- Motor Control
  Header located on the side           |   \----- Enable Parity Checking
  --------------------------           \--------- Drive ID, binary - use
 (Back) A B (Front of drive)                      ID 0 (no jumpers) for
        C D                                       single drive install
 A-B  Drive from Power Connector (factory default)
 A-C  Drive from SCSI Bus
 A-C&B-D  Drive from Power Connector and Provide to SCSI Bus
 B-D  Only provide to SCSI Bus


                             ST-1201NS
                         94351-200S Swift

       UNFORMATTED CAPACITY (MB) ________________201
       FORMATTED CAPACITY (36 SECTORS) (MB) _____177
       ACTUATOR TYPE ____________________________VOICE COIL
       TRACKS ___________________________________9,612
       CYLINDERS ________________________________1,068
       HEADS ____________________________________9
       DISCS ____________________________________5
       MEDIA TYPE _______________________________THIN FILM
       RECORDING METHOD _________________________RLL
       TRANSFER RATE (mbytes/sec) _______________1.25
       SPINDLE SPEED (RPM) ______________________3,600
       INTERFACE ________________________________SCSI
       TPI (TRACKS PER INCH) ____________________1,350
       BPI (BITS PER INCH) ______________________28,282
       AVERAGE ACCESS (ms) ______________________15
       SINGLE TRACK SEEK (ms) ___________________4
       MTBF (power-on hours) ____________________70,000
       POWER REQUIREMENTS: +12V START-UP (amps) _2.5
                           +12V TYPICAL (amps) __0.7
                           +5V START-UP (amps) __0.75
                           +5V TYPICAL (amps) ___0.4
                           TYPICAL (watts) ______11
                           MAXIMUM (watts) ______34
       BUFFERED STEP PULSE RATE (micro sec) _____6-200
       WRITE PRECOMP (cyl) ______________________N/A (1069)
       REDUCED WRITE CURRENT (cyl) ______________N/A (1069)
       LANDING ZONE (cyl) _______________________AUTO PARK
       IBM AT DRIVE TYPE ________________________0 or NONE

Already low-level formatted at the factory.


                          Swift Remote LED Option

               Front View of Drive Without the Plastic Bezel

                                  /---+---\
                                  | A | B |    B = Anode
                                  +---+---|    D = Cathode
                                  | C | D |
              ...=================#===#===#=====P=W=A===...


        o Default jumper at C-D for LED mounted on drive PWA
        o To use remote LED, remove jumper and extend B (Anode)
          and D (Cathode).
        o Swift LED kit 75912397 allows connection to a remote LED
        o Swift LED kit 95913369 has an LED for attachment to the
          system front bezel or a 5.25-inch frame kit

Seagate reserves the right to change, without notice, product
offerings or specifications. (6/26/90)